Part Datasheet Search > Maxim Integrated > MAX1185 Datasheet PDF > MAX1185 Datasheet Pages 10/21
MAX1185 Datasheet - Maxim Integrated
| Manufacturer: | Maxim Integrated |
| Case Package: | TQFP-48 |
| Description: | Dual 10Bit, 20MSPS, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs |
| Pictures: |
MAX1185Datasheet PDF
Page:
of 21 Go
If the format of the manual is confusing, please download and read the original PDF file.
Detailed Description
The MAX1185 uses a nine-stage, fully-differential,
pipelined architecture (Figure 1) that allows for high-
speed conversion while minimizing power consumption.
Samples taken at the inputs move progressively through
the pipeline stages every half-clock cycle. Including the
delay through the output latch, the total clock-cycle
latency is five clock cycles.
1.5-bit (2-comparator) flash ADCs convert the held input
voltages into a digital code. The digital-to-analog con-
verters (DACs) convert the digitized results back into
analog voltages, which are then subtracted from the
original held input signals. The resulting error signals
are then multiplied by two and the residues are passed
along to the next pipeline stages, where the process is
repeated until the signals have been processed by all
nine stages. Digital error correction compensates for
ADC comparator offsets in each of these pipeline
stages and ensures no missing codes.
Both input channels are sampled on the rising edge of
the clock and the resulting data is multiplexed at the
output. CHA data is updated on the rising edge (five
clock cycles later) and CHB data is updated on the
falling edge (5.5 clock cycles later) of the clock signal.
The A/B indicator follows the clock signal with a typical
delay time of 6ns and remains high when CHA data is
updated and low when CHB data is updated.
Input Track-and-Hold (T/H) Circuits
Figure 2 displays a simplified functional diagram of the
input track-and-hold (T/H) circuits in both track and hold
mode. In track mode, switches S1, S2a, S2b, S4a, S4b,
S5a, and S5b are closed. The fully differential circuits
sample the input signals onto the two capacitors (C2a
and C2b) through switches S4a and S4b. S2a and S2b
set the common mode for the amplifier input, and open
simultaneously with S1, sampling the input waveform.
Switches S4a and S4b are then opened before switches
S3a and S3b connect capacitors C1a and C1b to the out-
put of the amplifier and switch S4c is closed. The result-
ing differential voltages are held on capacitors C2a and
C2b. The amplifiers are used to charge capacitors C1a
and C1b to the same values originally held on C2a and
C2b. These values are then presented to the first stage
quantizers and isolate the pipelines from the fast-chang-
ing inputs. The wide input bandwidth T/H amplifiers allow
the MAX1185 to track and sample/hold analog inputs of
high frequencies (> Nyquist). Both ADC inputs (INA+,
INB+, INA-, and INB-) can be driven either differentially or
single-ended. Match the impedance of INA+ and INA- as
well as INB+ and INB- and set the common-mode volt-
age to midsupply (V
DD
/2) for optimum performance.
MAX1185
Dual 10-Bit, 20Msps, 3V, Low-Power ADC with
Internal Reference and Multiplexed Parallel Outputs
10 ______________________________________________________________________________________
Pin Description (continued)
PIN NAME FUNCTION
41 D6A/B
Three-State Digital Output, Bit 6. Depending on status of A/B, output data reflects channel A
or channel B data.
42 D7A/B
Three-State Digital Output, Bit 7. Depending on status of A/B, output data reflects channel A
or channel B data.
43 D8A/B
Three-State Digital Output, Bit 8. Depending on status of A/B, output data reflects channel A
or channel B data.
44 D9A/B
Three-State Digital Output, Bit 9 (MSB). Depending on status of A/B, output data reflects
channel A or channel B data.
45 REFOUT
Internal Reference Voltage Output. May be connected to REFIN through a resistor or a
resistor-divider.
46 REFIN Reference Input. V
REFIN
= 2 x (V
REFP
- V
REFN
). Bypass to GND with a > 1nF capacitor.
47 REFP
Positive Reference Input/Output. Conversion range is ± (V
REFP
- V
REFN
). Bypass to GND with
a > 0.1µF capacitor.
48 REFN
Negative Reference Input/Output. Conversion range is ± (V
REFP
- V
REFN
). Bypass to GND with
a > 0.1µF capacitor.
— EP Exposed Pad. Connect to analog ground.
Part Datasheet PDF Search
72,405,303 Parts Datasheet PDF, Update more than 5,000 PDF files ervery day.