Part Datasheet Search > PCA9538 Datasheet PDF
Images are for reference

PCA9538 Datasheet PDF

Part Series:PCA9538 Series
Description:Remote 8Bit I2C and SMBus Low-Power I/O Expander With Interrupt Output, Reset, and Config Registers
Document:PCA9538ABSHP Datasheet PDF (158 Pages)

PCA9538 Datasheet PDF

158 Pages
NXP
I2C/SMBus GPIO Expander 100kHz/400kHz 5.5V Automotive 16Pin TSSOP Bulk
158 Pages
NXP
I2C/SMBus GPIO Expander 100kHz/400kHz 5.5V Automotive 16Pin SO T/R
158 Pages
NXP
I2C/SMBus GPIO Expander 100kHz/400kHz 5.5V Automotive 16Pin SO Bulk
44 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin TVSOP T/R
37 Pages
TI
TEXAS INSTRUMENTS PCA9538PWR I/O Expander, 8Bit, 400kHz, I2C, SMBus, 2.3V, 5.5V, TSSOP
37 Pages
TI
TEXAS INSTRUMENTS PCA9538PW I/O Expander, 8Bit, 400kHz, I2C, SMBus, 2.3V, 5.5V, TSSOP
37 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin SOIC T/R
37 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin SSOP T/R
37 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin TSSOP Tube
37 Pages
TI
TEXAS INSTRUMENTS PCA9538DW I/O Expander, 8Bit, 400kHz, I2C, SMBus, 2.3V, 5.5V, SOIC
37 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin TSSOP T/R
37 Pages
TI
I2C/SMBus GPIO Expander 400kHz 5.5V 16Pin SSOP Tube
37 Pages
TI
Remote 8Bit I2C and SMBus Low-Power I/O Expander With Interrupt Output, Reset, and Config Registers 16-SSOP -40℃ to 85℃
37 Pages
TI
Remote 8Bit I2C and SMBus Low-Power I/O Expander With Interrupt Output, Reset, and Config Registers
35 Pages
NXP
I2C/SMBus GPIO Expander 100kHz/400kHz 5.5V Automotive 16Pin TSSOP T/R
34 Pages
NXP
I2C/SMBus GPIO Expander 100kHz/400kHz 5.5V 16Pin TSSOP

PCA9538 - TI Specifications

TYPE
DESCRIPTION
Case/Package
TSSOP-16
show more

PCA9538 - TI Function Overview

This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)].
The PCA9538 consists of one 8-bit Configuration (input or output selection), Input Port, Output Port, and Polarity Inversion (active high or active low) registers. At power on, the I/Os are configured as inputs. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input Port or Output Port register. The polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by the system master.
The system master can reset the PCA9538 in the event of a timeout or other improper operation by asserting a low in the RESET input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus state machine. The RESET pin causes the same reset/initialization to occur without powering down the part.
The PCA9538 open-drain interrupt (INT) output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9538 can remain a simple slave device.
The device outputs (latched) have high-current drive capability for directly driving LEDs. It has low current consumption.
Two hardware pins (A0 and A1) are used to program and vary the fixed I2C address and allow up to four devices to share the same I2C bus or SMBus.
Low Standby Current Consumption of 1 μA Max
I2C to Parallel Port Expander
Open-Drain Active-Low Interrupt Output
Active-Low Reset Input
Operating Power-Supply Voltage Range of 2.3 V to 5.5 V
5-V Tolerant I/O Ports
400-kHz Fast I2C Bus
Two Hardware Address Pins Allow up to Four Devices on the I2C/SMBus
Input/Output Configuration Register
Polarity Inversion Register
Power-Up With All Channels Configured as Inputs
No Glitch on Power Up
Noise Filter on SCL/SDA Inputs
Latched Outputs With High-Current Drive Maximum Capability for Directly Driving LEDs
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
ESD Protection Exceeds JESD 22
2000-V Human-Body Model (A114-A)
200-V Machine Model (A115-A)
1000-V Charged-Device Model (C101)
All trademarks are the property of their respective owners.
show more
Part Datasheet PDF Search
72,405,303 Parts Datasheet PDF, Update more than 5,000 PDF files ervery day.