LPC4330FET180 Datasheet PDF - NXP

Overview

●The LPC4330FET180 is an ARM Cortex-M4 based digital signal controller with an ARM Cortex-M0 coprocessor designed for embedded applications requiring signal processing. The ARM Cortex-M4 core offers single-cycle Multiply-Accumulate and SIMD instructions and a hardware floating-point unit to support signal processing while the M0 coprocessor handles I/O and digital control processing. The LPC4330FET180 includes 264 kB of data memory, two High Speed USB 2.0 Host/OTG/Devices, advanced configurable peripherals such as the State Configurable Timer (SCT), Serial General Purpose I/O (SGPIO), and SPI Flash Interface (SPIFI) as well as Ethernet, an external memory controller and multiple digital and analog peripherals.

●MoreLess

●## Features

● ARM Cortex-M4 processor, running at frequencies of up to 204 MHz

● ARM Cortex-M4 built-in Memory Protection Unit (MPU) supporting eight regions

● ARM Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC)

● Hardware floating-point unit

● Non-maskable Interrupt (NMI) input

● JTAG and Serial Wire Debug (SWD)

● System tick timer

● ARM Cortex-M0 co-processor running at frequencies of up to 204 MHz

● 256 kB SRAM for code and data use

● Two 32 kB SRAM blocks with separate bus access

● 32 kB ROM containing boot code and on-chip software drivers

● 32 bit One-Time Programmable (OTP) memory for customer use

● Serial GPIO (SGPIO) interface

● State Configurable Timer (SCT) subsystem on AHB

● Quad SPI Flash Interface (SPIFI) with four lanes and up to 40 MB per second

● 10/100T Ethernet MAC with RMII and MII interfaces and DMA support

● One High-speed USB 2.0 Host/Device/OTG interface with DMA support

● One High-speed USB 2.0 Host/Device interface with DMA support

● One 550 UART with DMA support and full modem interface

● Three 550 USARTs with DMA and synchronous mode support

● One C_CAN 2.0B controller with one channel

● Two SSP controllers with FIFO and multi-protocol support

● One SPI controller

● One Fast-mode Plus I2C-bus interface with rates of up to 1 Mbit/s

● One Fast-mode I2C-bus interface

● Two I2S interfaces

● External Memory Controller (EMC) supporting external SRAM, ROM, flash, SDRAM

● Secure Digital Input Output (SDIO) card interface

● Eight-channel General-Purpose DMA (GPDMA) controller

● Up to 118 General-Purpose Input/Output (GPIO) pins

● Four general-purpose timer/counters with capture and match capabilities

● One motor control Pulse Width Modulator (PWM) for three-phase motor control

● One Quadrature Encoder Interface (QEI)

● Repetitive Interrupt timer (RI timer)

● Windowed watchdog timer (WWDT)

● Ultra-low power Real-Time Clock (RTC) on separate power domain

● Alarm timer; can be battery powered

● One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s

● Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s

● Two 128-bit secure OTP memories for AES key storage and customer use

● Crystal oscillator with an operating range of 1 MHz to 25 MHz

● 12 MHz Internal RC (IRC) oscillator trimmed to 1 % accuracy

● Ultra-low power Real-Time Clock (RTC) crystal oscillator

● Three PLLs allow CPU operation up to the maximum CPU rate

● Clock output

● Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip DC-to-DC converter

● RTC power domain can be powered separately by a 3 V battery supply

● Four reduced power modes

● Processor wake-up from Sleep mode via wake-up interrupts

● Brownout detect with four separate thresholds for interrupt and forced reset

● Power-On Reset (POR)

● see selection guide for features per type

●## Target Applications

● Industrial

● Consumer

● White goods

● RFID readers

● e-Metering

●## Features