• 32-Bit Version 1 ColdFire® Central Processor Unit (CPU)
●– Up to 50.33-MHz ColdFire V1 CPU above 2.4V, 40-MHz CPU above 2.1V, and 20-MHz CPU above 1.8V, across temperature range
●– Provides 0.94 Dhrystone 2.1 MIPS per MHz performance when running from internal RAM(0.76 DMIPS/MHz from flash)
●– Implements Instruction Set Revision C (ISA_C)
●– Support for up to 30 peripheral interrupt requests and seven software interrupts
●• On-Chip Memory
●– Flash read/program/erase over full operating voltage and temperature
●– Random-access memory (RAM)
●– Security circuitry to prevent unauthorized access to RAM and flash contents
●• Power-Saving Modes
●– Two low power stop modes; reduced power wait mode
●– Peripheral clock enable register can disable clocks to unused modules, reducing currents; allows clocks to remain enabled to specific peripherals in stop3 mode
●– Very low power external oscillator can be used in stop3 mode to provide accurate clock to active peripherals
●– Very low power real time counter for use in run, wait, and stop modes with internal and external clock sources
●– 6 μs typical wake up time from stop modes
●• Clock Source Options
●– Oscillator (XOSC) — Loop-control Pierce oscillator;
● Crystal or ceramic resonator range of 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz
●– Internal Clock Source (ICS) — FLL controlled by internal or external reference; precision trimming of internal reference allows 0.2% resolution and 2% deviation; supports CPU freq. from 2 to 50.33 MHz
●• System Protection
●– Watchdog computer operating properly (COP) reset with option to run from dedicated 1-kHz internal clock source or bus clock
●– Low-voltage detection with reset or interrupt; selectable trip points
●– Illegal opcode and illegal address detection with programmable reset or exception response
●– Flash block protection
●• Development Support
●– Single-wire background debug interface
●– 4 PC plus 2 address (optional data) breakpoint registers with programmable 1- or 2-level trigger response
●– 64-entry processor status and debug data trace buffer with programmable start/stop conditions
●• ADC — 24-channel, 12-bit resolution; 2.5 μs conversion time; automatic compare function; 1.7 mV/°C temperature sensor; internal bandgap reference channel; operation in stop3; fully functional from 3.6V to 1.8V
●• ACMPx — Two analog comparators with selectable interrupt on rising, falling, or either edge of comparator output; compare option to fixed internal bandgap reference voltage; outputs can be optionally routed to TPM module; operation in stop3
●• SCIx — Two SCIs with full duplex non-return to zero (NRZ); LIN master extended break generation; LIN slave extended break detection; wake up on active edge
●• SPIx— Two serial peripheral interfaces with Full-duplex or single-wire bidirectional; Double-buffered transmit and receive; MSB-first or LSB-first shifting
●• IICx — Two IICs with; Up to 100 kbps with maximum bus loading; Multi-master operation; Programmable slave address; Interrupt driven byte-by-byte data transfer; supports broadcast mode and 10 bit addressing
●• TPMx — One 6-channel and two 3-channel; Selectable input capture, output compare, or buffered edge- or center-aligned PWMs on each channel
●• RTC — 8-bit modulus counter with binary or decimal based prescaler; External clock source for precise time base, time-of-day, calendar or task scheduling functions; Free running on-chip low power oscillator (1 kHz) for cyclic wake-up without external components
●• Input/Output
●– 70 GPIOs and 1 input-only and 1 output-only pin
●– 16 KBI interrupts with selectable polarity
●– Hysteresis and configurable pull-up device on all input pins; Configurable slew rate and drive strength on all output pins.
●– SET/CLR registers on 16 pins (PTC and PTE)
●– 16 bits of Rapid GPIO connected to the CPU’s high-speed local bus with set, clear, and toggle functionality
