The TI MSP family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the devices to wake up from low-power modes to active mode in less than 5 µs.
●The MSP430F51x2 microcontrollers include two 16-bit high-resolution timers, two USCIs (USCI_A0 and USCI_B0), a 32-bit hardware multiplier, a high-performance 10-bit ADC, an on-chip comparator, a 3-channel DMA, 5-V tolerant I/Os, and up to 29 I/O pins.
●The MSP430F51x1 microcontrollers include two 16-bit high-resolution timers, two USCIs (USCI_A0 and USCI_B0), a 32-bit hardware multiplier, an on-chip comparator, a 3-channel DMA, 5-V tolerant I/Os, and up to 29 I/O pins.
●Typical applications for these devices include analog and digital sensor systems, LED lighting, digital power supplies, motor controls, remote controls, thermostats, digital timers, and hand-held meters.
● Low Supply-Voltage Range: 3.6 V Down to 1.8 V
● Ultra-Low Power Consumption
● Active Mode (AM): 180 µA/MHz
● Standby Mode (LPM3 WDT Mode, 3 V): 1.1 µA
● Off Mode (LPM4 RAM Retention, 3 V): 0.9 µA
● Shutdown Mode (LPM4.5, 3 V): 0.25 µA
● Wake up From Standby Mode in Less Than 5 µs
● 16-Bit RISC Architecture, Extended Memory, 40-ns Instruction Cycle Time
● Flexible Power-Management System
● Fully Integrated LDO With Programmable Regulated Core Supply Voltage
● Supply Voltage Supervision, Monitoring, and Brownout
● Unified Clock System
● FLL Control Loop for Frequency Stabilization
● Low-Power Low-Frequency Internal Clock Source (VLO)
● Low-Frequency Trimmed Internal Reference Source (REFO)
● 32-kHz Crystals (XT1)
● High-Frequency Crystals up to 25 MHz (XT1)
● Hardware Multiplier Supports 32-Bit Operations
● 3-Channel DMA
● Up to Twelve 5-V-Tolerant Digital Push/Pull I/Os With up to 20-mA Drive Strength
● 16-Bit Timer TD0 With Three Capture/Compare Registers and Support of High-Resolution Mode
● 16-Bit Timer TD1 With Three Capture/Compare Registers and Support of High-Resolution Mode
● 16-Bit Timer TA0 With Three Capture/Compare Registers
● Universal Serial Communication Interfaces (USCIs)
● USCI_A0 Supports:
● Enhanced UART Supports Automatic Baud-Rate Detection
● IrDA Encoder and Decoder
● Synchronous SPI
● USCI_B0 Supports:
● I2C
● Synchronous SPI
● 10-Bit 200-ksps Analog-to-Digital Converter (ADC)
● Internal Reference
● Sample-and-Hold
● Autoscan Feature
● Up to 8 External Channels and 2 Internal Channels, Including Temperature Sensor
● Up to 16-Channel On-Chip Comparator Including an Ultra-Low-Power Mode(1)
● Serial Onboard Programming, No External Programming Voltage Needed
● Summarizes Available Family Members
● Available in 40-Pin QFN (RSB), 38-Pin TSSOP (DA), and 40-Pin Die-Sized BGA (YFF) Packages
● For Complete Module Descriptions, See the
