The Texas Instruments MSP430 family of ultra-low-power microcontrollers consists of several devices that feature different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in 3 µs (typical).
●The MSP430F665x and MSP430F565x series are microcontroller configurations with four 16-bit timers, a high-performance 12-bit analog-to-digital converter (ADC) , three universal serial communication interfaces (USCIs), a hardware multiplier, DMA, a real-time clock (RTC) module with alarm capabilities, a comparator, USB 2.0, and up to 74 I/O pins.
●The MSP430F645x and MSP430F535x series are microcontroller configurations with an integrated 3.3-V LDO, four 16-bit timers, a high-performance 12-bit ADC, three USCIs, a hardware multiplier, DMA, an RTC module with alarm capabilities, a comparator, and up to 74 I/O pins.
●Typical applications for these devices include analog and digital sensor systems, digital motor control, remote controls, thermostats, digital timers, and hand-held meters.
● Low Supply Voltage Range: 3.6 V Down to 1.8 V
● Ultra-Low-Power Consumption
● Active Mode (AM):
●All System Clocks Active:
●295 µA/MHz at 8 MHz, 3.0 V, Flash Program Execution (Typical)
● Standby Mode (LPM3):
●Watchdog With Crystal, and Supply Supervisor Operational, Full RAM Retention, Fast Wake-Up:
●2.0 µA at 2.2 V, 2.2 µA at 3.0 V (Typical)
● Shutdown, RTC Mode (LPM3.5):
●Shutdown Mode, Active Real-Time Clock (RTC) With Crystal:
●1.1 µA at 3.0 V (Typical)
● Shutdown Mode (LPM4.5):
●0.45 µA at 3.0 V (Typical)
● Wake Up From Standby Mode in 3 µs (Typical)
● 16-Bit RISC Architecture, Extended Memory, up to 20-MHz System Clock
● Flexible Power Management System
● Fully Integrated LDO With Programmable Regulated Core Supply Voltage
● Supply Voltage Supervision, Monitoring, and Brownout
● Unified Clock System
● FLL Control Loop for Frequency Stabilization
● Low-Power Low-Frequency Internal Clock Source (VLO)
● Low-Frequency Trimmed Internal Reference Source (REFO)
● 32-kHz Crystals (XT1)
● High-Frequency Crystals Up to 32 MHz (XT2)
● Four 16-Bit Timer With 3, 5, or 7 Capture/Compare Registers
● Three Universal Serial Communication Interfaces (USCIs)
● USCI_A0, USCI_A1, and USCI_A2 Each Support:
● Enhanced UART Supports Auto-Baudrate Detection
● IrDA Encoder and Decoder
● Synchronous SPI
● USCI_B0, USCI_B1, and USCI_B2 Each Support:
● I2C
● Synchronous SPI
● Full-Speed Universal Serial Bus (USB)
● Integrated USB-PHY
● Integrated 3.3-V and 1.8-V USB Power System
● Integrated USB-PLL
● Eight Input and Eight Output Endpoints
● 12-Bit Analog-to-Digital Converter (ADC) With Internal Shared Reference, Sample-and-Hold, and Autoscan Feature
● Two 12-Bit Digital-to-Analog Converters (DACs) With Synchronization
● Voltage Comparator
● Integrated LCD Driver With Contrast Control for up to 160 Segments
● Hardware Multiplier Supports 32-Bit Operations
● Serial Onboard Programming, No External Programming Voltage Needed
● Six-Channel Internal DMA
● RTC Module With Supply Voltage Backup Switch
