DEVICE OVERVIEW
●This document contains device specific information for the following devices:
● • PIC18F2410 • PIC18LF2410
● • PIC18F2510 • PIC18LF2510
● • PIC18F2515 • PIC18LF2515
● • PIC18F2610 • PIC18LF2610
● • PIC18F4410 • PIC18LF4410
● • PIC18F4510 • PIC18LF4510
● • PIC18F4515 • PIC18LF4515
● • PIC18F4610 • PIC18LF4610
●This family offers the advantages of all PIC18 microcontrollers – namely, high computational performance at an economical price – with the addition of high-endurance, Flash program memory. On top of these features, the PIC18F2X1X/4X1X family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications.
●Power-Managed Modes:
●• Run: CPU On, Peripherals On
●• Idle: CPU Off, Peripherals On
●• Sleep: CPU Off, Peripherals Off
●• Idle mode Currents Down to 3.0 μA Typical
●• Sleep mode Currents Down to 20 nA Typical
●• Timer1 Oscillator: 1.8 μA, 32 kHz, 2V
●• Watchdog Timer: 2.1 μA
●• Two-Speed Oscillator Start-up
●Peripheral Highlights:
●• High-Current Sink/Source 25 mA/25 mA
●• Up to 2 Capture/Compare/PWM (CCP) modules, One with Auto-Shutdown (28-pin devices)
●• Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):
● - One, two or four PWM outputs
● - Selectable polarity
● - Programmable dead time
● - Auto-shutdown and auto-restart
●• Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C™ Master and Slave modes
●• Enhanced Addressable USART module:
● - Supports RS-485, RS-232 and LIN 1.2
● - RS-232 operation using internal oscillator block (no external crystal required)
● - Auto-wake-up on Start bit
● - Auto-Baud Detect
●• 10-Bit, Up to 13-Channel Analog-to-Digital Converter module (A/D):
● - Auto-acquisition capability
● - Conversion available during Sleep
●• Dual Analog Comparators with Input Multiplexing
●• Programmable 16-Level High/Low-Voltage Detection (HLVD) module:
● - Supports interrupt on High/Low-Voltage Detection
●Flexible Oscillator Structure:
●• Four Crystal modes, Up to 40 MHz
●• 4x Phase Lock Loop (PLL) – Available for Crystal and Internal Oscillators
●• Two External RC modes, Up to 4 MHz
●• Two External Clock modes, Up to 40 MHz
●• Internal Oscillator Block:
● - 8 user-selectable frequencies, from 31 kHz to 8 MHz
● - Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL
● - User-tunable to compensate for frequency drift
●• Secondary Oscillator using Timer1 @ 32 kHz
●• Fail-Safe Clock Monitor:
● - Allows for safe shutdown if peripheral clock stops
●Special Microcontroller Features:
●• C Compiler Optimized Architecture:
● - Optional extended instruction set designed to optimize re-entrant code
●• 100,000 Erase/Write Cycle Flash Program Memory Typical
●• Three Programmable External Interrupts
●• Four Input Change Interrupts
●• Priority Levels for Interrupts
●• 8 x 8 Single-Cycle Hardware Multiplier
●• Extended Watchdog Timer (WDT):
● - Programmable period from 4 ms to 131s
●• Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins
●• In-Circuit Debug (ICD) via Two Pins
●• Wide Operating Voltage Range: 2.0V to 5.5V
●• Programmable Brown-out Reset (BOR) with Software Enable Option