The ultra-low-power STM32L100C6 and STM32L100R8/RB devices incorporate the connectivity power of the universal serial bus (USB) with the high-performance ARM® Cortex®-M3 32-bit RISC core operating at a frequency of 32 MHz (33.3 DMIPS), a memory protection unit (MPU), high-speed embedded memories (Flash memory up to 128 Kbytes and RAM up to 10 Kbytes) and an extensive range of enhanced I/Os and peripherals connected to two APB buses.
●All the devices offer a 12-bit ADC, 2 DACs and 2 ultra-low-power comparators, six general-purpose 16-bit timers and two basic timers, which can be used as time bases.
●Moreover, the STM32L100C6 and STM32L100R8/RB devices contain standard and advanced communication interfaces: up to two I2Cs and SPIs, three USARTs and a USB.
●They also include a real-time clock with sub-second counting and a set of backup registers that remain powered in Standby mode.
●Finally, the integrated LCD controller has a built-in LCD voltage generator that allows to drive up to 8 multiplexed LCDs with contrast independent of the supply voltage.
●The ultra-low-power STM32L100C6 and STM32L100R8/RB devices operate from a 1.8 to 3.6 V power supply. They are available in the -40 to +85 °C temperature range. A comprehensive set of power-saving modes allows the design of low-power applications.
●Key Features
● Ultra-low-power platform
● 1.8 V to 3.6 V power supply
● -40°C to 85°C temperature range
● 0.3 µA Standby mode (2 wakeup pins)
● 0.9 µA Standby mode + RTC
● 0.57 µA Stop mode (16 wakeup lines)
● 1.2 µA Stop mode + RTC
● 9 µA Low-power run mode
● 214 µA/MHz Run mode
● 10 nA ultra-low I/O leakage
● < 8 µs wakeup time
● Core: 32-bit ARM® Cortex® -M3 CPU
● From 32 kHz up to 32 MHz max
● 1.25 DMIPS/MHz (Dhrystone 2.1)
● Memory protection unit
● Reset and supply management
● Ultra-safe, low-power BOR (brownout reset) with 5 selectable thresholds
● Ultra-low-power POR/PDR
● Programmable voltage detector (PVD)
● Clock sources
● 1 to 24 MHz crystal oscillator
● 32 kHz oscillator for RTC with calibration
● High-speed internal 16 MHz
● Internal low-power 37 kHz RC
● Internal multispeed low-power 65 kHz to 4.2 MHz
● PLL for CPU clock and USB (48 MHz)
● Pre-programmed bootloader
● USART supported
● Development support
● Serial wire debug supported
● JTAG supported
● Up to 51 fast I/Os (42 I/Os 5V tolerant), all mappable on 16 external interrupt vectors
● Memories
● Up to 128 Kbytes of Flash memory with ECC
● Up to 10 Kbytes of RAM
● Up to 2 Kbytes of true EEPROM with ECC
● 20-byte backup register
● LCD Driver for up to 8x28 segments
● Analog peripherals
● 12-bit ADC 1 Msps up to 20 channels
● 12-bit DAC 2 channels with output buffers
● Two ultra-low-power comparators
● Seven DMA controller channels
● Eight communication interface peripherals
● One USB 2.0
● Three USARTs (ISO 7816, IrDA)
● Two SPIs (16 Mbit/s)
● Two I2Cs (SMBus/PMBus)
● Ten timers:
● Six 16-bit timers with up to 4 IC/OC/PWM channels
● Two 16-bit basic timers
● Two watchdog timers (independent and window)
● CRC calculation unit
● All packages ECOPACK® 2