W83627HF-AW Datasheet PDF - Winbond Electronics

GENERAL DESCRIPTION

●The W83627HF and W83627F are evolving product fromWinbond"s most popular I/O family. They

●feature a whole new interface, namely LPC（Low Pin Count）interface, which will be supported in the next generation Intel chip-set. This interface as its name suggests is to provide an economical implementation of I/O"s interface with lower pin countand still maintains equivalent performance as its ISA interface counterpart. Approximately 40 pin counts are saved in LPC I/O comparing to ISA implementation. With this additional freedom, we can implement more devices on a single chip as demonstrated in W83627F/HF"s integration of Game Port and MIDI Port.It is fully transparentin terms of software which means no BIOS or device driver update is needed except chip-specific configuration.

●FEATURES

●General

●• Meet LPC Spec. 1.0

●•Support LDRQ#（LPC DMA）, SERIRQ （serial IRQ）

●• Include all the features of Winbond I/O W83977TF and W83977EF

●• Integrate Hardware Monitor functions

●• Compliant with Microsoft PC98/PC99 Hardware Design Guide

●•Support DPM （Device Power Management）, ACPI

●• Programmable configuration settings

●• Single 24 or 48 MHz clock input

●FDC

●• Compatible with IBM PC AT disk drive systems

●• Variable write pre-compensation with track selectable capability

●• Support vertical recording format

●• DMA enable logic

●• 16-byte data FIFOs

●• Support floppy disk drives and tape drives

●• Detects all overrun and underrun conditions

●• Built-in address mark detection circuit to simplify the read electronics

●• FDD anti-virus functions with software write protect and FDD write enable signal （write data

●signal was forced to be inactive）

●• Support up to four 3.5-inch or 5.25-inch floppy disk drives

●• Completely compatible with industry standard 82077

●• 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate

●• Support 3-mode FDD, and its Win95/98 driver

●UART

●• Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs

●•MIDI compatible

●• Fully programmable serial-interface characteristics：

●─5, 6, 7 or 8-bit characters

●─Even, odd or no parity bit generation/detection

●─1, 1.5 or 2 stop bits generation

●• Internal diagnostic capabilities：

●─Loop-back controls for communications link fault isolation

●─Break, parity, overrun, framing error simulation

●• Programmable baud generator allows division of 1.8461 MHz and 24 MHz by 1 to （216-1）

●• Maximum baud rate up to 921k bps for 14.769 MHz and 1.5M bps for 24 MHz

●Infrared

●• Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps

●Parallel Port

●• Compatible with IBM parallel port

●• Support PS/2 compatible bi-directional parallel port

●• Support Enhanced Parallel Port（EPP）−Compatible with IEEE 1284 specification

●• Support Extended Capabilities Port（ECP）−Compatible with IEEE 1284 specification

●• Extension FDD mode supports disk drive B; and Extension 2FDD mode supports disk drives A

●and B through parallel port

●• Enhanced printer port back-drive current protection

●Keyboard Controller

●• 8042 based with optional F/W from AMIKKEYTM -2,or customer code with 2K bytes of program

●mable ROM, and 256 bytes of RAM

●• Asynchronous Access to Two Data Registers and One status Register

●• Software compatibility with the 8042

●• Support PS/2 mouse

●• Support port 92

●• Support both interrupt and polling modes

●• Fast Gate A20 and Hardware Keyboard Reset

●• 8 Bit Timer/ Counter

●• Support binary and BCD arithmetic

●• 6 MHz, 8 MHz, 12 MHz, or 16 MHz operating frequency

●Game Port

●• Support two separate Joysticks

●• Support every Joystick two axis （X,Y）and two button （A,B）controllers

●MIDI Port

●• The baud rate is 31.25 Kbaud

●• 16-byte input FIFO

●• 16-byte output FIFO

●General Purpose I/O Ports

●• 22 programmable general purpose I/O ports

●• General purpose I/O ports can serve as simple I/O ports, interrupt steering inputs, watch dog

●timer output, power LED output, infrared I/O pins, KBC control I/O pins, suspend LED output,

●RSMRST# signal, PWROK signal, Beep output

●• Functional in power down mode （GP1 only） OnNow Functions

●• Keyboard Wake-Up by programmable keys

●• Mouse Wake-Up by programmable buttons

●• CIR Wake-Up by programmable keys

●• On Now Wake-Up from all of the ACPI sleeping states （S1-S5）

●Hardware Monitor Functions （Only for W83627HF）

●• 5 VID input pins for CPU Vcore identification

●• 3 thermal inputs from optionally remote thermistors or 2N3904 transistors or PentiumTM II

●（Deschutes）thermal diode output

●• 7 positive voltage inputs （typical for +12V, -12V, +5V, -5V, +3.3V, VcoreA, VcoreB）

●• 2 intrinsic voltage monitoring （typical for Vbat, +5VSB）

●• 3 fan speed monitoring inputs

●• 2 fan speed control

●• Build in Case open detection circuit

●• WATCHDOG comparison of all monitored values

●• Programmable hysteresis and setting points for all monitored items

●• Over temperature indicate output

●• Automatic Power On voltage detection Beep

●• Issue SMI#, IRQ, OVT# to activate system protection

●•Intel LDCMTM / Acer ADMTM compatible

●Package

●• 128-pin PQFP