LPC1315FBD48 Datasheet PDF - NXP

General description

●The LPC1315/16/17/45/46/47 are ARM Cortex-M3 based microcontrollers for embedded

●applications featuring a high level of integration and low power consumption. The ARM

●Cortex-M3 is a next generation core that offers system enhancements such as enhanced

●debug features and a higher level of support block integration.

●Features and benefits

● System:

●  ARM Cortex-M3 r2p1 processor, running at frequencies of up to 72 MHz.

●  ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).

●  Non Maskable Interrupt (NMI) input selectable from several input sources.

●  System tick timer.

● Memory:

●  Up to 64 kB on-chip flash program memory with a 256 byte page erase function.

●  In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader software. Flash updates via USB supported.

●  Up to 4 kB on-chip EEPROM data memory with on-chip API support.

●  Up to 12 kB SRAM data memory.

●  16 kB boot ROM with API support for USB API, power control, EEPROM, and flash IAP/ISP.

● Debug options:

●  Standard JTAG test interface for BSDL.

●  Serial Wire Debug.

●  Support for ETM ARM Cortex-M3 debug time stamping.

● Digital peripherals:

●  Up to 51 General Purpose I/O (GPIO) pins with configurablepull-up/pull-down resistors, repeater mode, input inverter, and pseudo open-drain mode. Eight pins support programmable glitch filter.

●  Up to 8 GPIO pins can be selected as edge and level sensitive interrupt sources.

●  Two GPIO grouped interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.

●  High-current source output driver (20 mA) on one pin (P0_7).

●  High-current sink driver (20 mA) on true open-drain pins (P0_4 and P0_5).

●  Four general purpose counter/timers with a total of up to 8 capture inputs and 13 match outputs.

●  Programmable Windowed WatchDog Timer (WWDT) with a internal low-power WatchDog Oscillator (WDO).

●  Repetitive Interrupt Timer (RI Timer).

● Analog peripherals:

●  12-bit ADC with eight input channels and sampling rates of up to 500 kSamples/s. 

●   Serial interfaces:

●  USB 2.0 full-speed device controller (LPC1345/46/47) with on-chip ROM-based USB driver library.

●  USART with fractional baud rate generation, internal FIFO, a full modem control handshake interface, and support for RS-485/9-bit mode and synchronous mode. USART supports an asynchronous smart card interface (ISO 7816-3).

●  Two SSP controllers with FIFO and multi-protocol capabilities.

●  I2C-bus interface supporting the full I2C-bus specification andFast-mode Plus with a data rate of up to 1 Mbit/s with multiple address recognition and monitor mode.

● Clock generation:

●  Crystal Oscillator with an operating range of 1 MHz to 25 MHz (system oscillator) with failure detector.

●  12 MHz high-frequency Internal RC oscillator (IRC) trimmed to 1 % accuracy over the entire voltage and temperature range. The IRC can optionally be used as a system clock.

●  Internal low-power, low-frequency WatchDog Oscillator (WDO) with programmable frequency output.

●  PLL allows CPU operation up to the maximum CPU rate with the system oscillator or the IRC as clock sources.

●  A second, dedicated PLL is provided for USB (LPC1345/46/47).

●  Clock output function with divider that can reflect the crystal oscillator, the main clock, the IRC, or the watchdog oscillator.

● Power control:

●  Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.

●  Power profiles residing in boot ROM allow optimized performance and minimized power consumption for any given application through one simple function call.

●  Processor wake-up from Deep-sleep and Power-down modes via reset, selectable GPIO pins, watchdog interrupt, or USB port activity.

●  Processor wake-up from Deep power-down mode using one special function pin.

●  Integrated PMU (Power Management Unit) to minimize power consumption during Sleep, Deep-sleep, Power-down, and Deep power-down modes.

●  Power-On Reset (POR).

●  Brownout detect with up to four separate thresholds for interrupt and forced reset.

● Unique device serial number for identification.

● Single 3.3 V power supply (2.0 V to 3.6 V).

● Temperature range 40 C to +85 C.

● Available as LQFP64, LQFP48, and HVQFN33 package.

● Applications

● Consumer

●    peripherals  

●    Handheld scanners

● Medical

● USB audio devices

● Industrial control