The Texas Instruments MSP430FR573x family of ultra-low-power microcontrollers consists of multiple devices that feature embedded FRAM nonvolatile memory, ultra-low-power 16-bit MSP430™ CPU, and different peripherals targeted for various applications. The architecture, FRAM, and peripherals, combined with seven low-power modes, are optimized to achieve extended battery life in portable and wireless sensing applications. FRAM is a new nonvolatile memory that combines the speed, flexibility, and endurance of SRAM with the stability and reliability of flash, all at lower total power consumption. Peripherals include a 10-bit analog-to-digital converter (ADC), a 16-channel comparator with voltage reference generation and hysteresis capabilities, three enhanced serial channels capable of I2C, SPI, or UART protocols, an internal DMA, a hardware multiplier, an RTC, five 16-bit timers, and digital I/Os.
● Embedded Microcontroller
● 16-Bit RISC Architecture up to 24-MHz Clock
● Wide Supply Voltage Range (2 to 3.6 V)
● 55°C to 85°C Operation
● Optimized Ultra-Low-Power Modes
● Active Mode: 81.4 µA/MHz (Typical)
● Standby (LPM3 With VLO): 6.3 µA (Typical)
● Real-Time Clock (LPM3.5 With Crystal): 1.5 µA
●(Typical)
● Shutdown (LPM4.5): 0.32 µA (Typical)
● Ultra-Low-Power Ferroelectric RAM (FRAM)
● Up to 16KB of Nonvolatile Memory
● Ultra-Low-Power Writes
● Fast Write at 125 ns per Word (16KB in 1 ms)
● Built-In Error Correction Coding (ECC) and
●Memory Protection Unit (MPU)
● Universal Memory = Program + Data + Storage
● 1015 Write Cycle Endurance
● Radiation Resistant and Nonmagnetic
● Intelligent Digital Peripherals
● 32-Bit Hardware
●Multiplier (MPY)
● Three-Channel Internal DMA
● Real-Time Clock (RTC) With Calendar and
●Alarm Functions
● Five 16-Bit Timers With up to Three
●Capture/Compare Registers
● 16-Bit Cyclic Redundancy Checker(CRC)
● High-Performance Analog
● 16-Channel Analog Comparator With Voltage
●Reference and Programmable Hysteresis
● 14-Channel 10-Bit Analog-to-Digital Converter
●With Internal Reference and Sample-and-Hold
● 200 ksps at 100-µA Consumption
● Enhanced Serial Communication
● eUSCI_A0 and eUSCI_A1 Support:
● UART With Automatic Baud-Rate Detection
● IrDA Encode and Decode
● SPI at Rates up to 10 Mbps
● eUSCI_B0 Supports:
● I2C With Multiple Slave Addressing
● SPI at Rates up to 10 Mbps
● Hardware UART Bootstrap Loader (BSL)
● Power Management System
● Fully Integrated LDO
● Supply Voltage Supervisor for Core and
●Supply Voltages With Reset Capability
● Always-On Zero-Power Brownout Detection
● Serial On-Board Programming With No External
●Voltage Needed
● Flexible Clock System
● Fixed-Frequency DCO With Six Selectable
●Factory-Trimmed Frequencies (Device Dependent)
● Low-Power Low-Frequency Internal Clock
●Source (VLO)
● 32-kHz Crystals (LFXT)
● High-Frequency Crystals (HFXT)
● Development Tools and Software
● Free Professional Development Environment
●(Code Composer Studio IDE)
● Low-Cost Full-Featured Kit
●(MSP-EXP430FR5739)
● Full Development Kit (MSP-FET430U40A)
● Target Board (MSP-TS430RHA40A)
● Family Members
● Variants and Available Packages Summarized in
● For Complete Module Descriptions, See the
●_MSP430FR57xx Family Users Guide_ (SLAU272)
● Supports Defense, Aerospace, and Medical Applications
● Controlled Baseline
● One Assembly and Test Site
● One Fabrication Site
● Available in Extended (55°C to 85°C) Temperature Range(1)
● Extended Product Life Cycle
● Extended Product-Change Notification
● Product Traceability
