The ultra-low-power STM32L100RC device incorporates the connectivity power of the universal serial bus (USB) with the high-performance ARM® Cortex®-M3 32-bit RISC core operating at a frequency of 32 MHz (33.3 DMIPS), a memory protection unit (MPU), high-speed embedded memories (Flash memory up to 256 Kbytes and RAM up to 16 Kbytes) and an extensive range of enhanced I/Os and peripherals connected to two APB buses.
●The STM32L100RC device offers one 12-bit ADC, two DACs, two ultra-low-power comparators, six general-purpose 16-bit timers and two basic timers, which can be used as time bases.
●Moreover, the STM32L100RC device contains standard and advanced communication interfaces: up to two I2Cs, three SPIs, two I2S, three USARTs, and an USB.
●It also includes a real-time clock and a set of backup registers that remain powered in Standby mode.
●Finally, the integrated LCD controller has a built-in LCD voltage generator that allows to drive up to 8 multiplexed LCDs with the contrast independent of the supply voltage.
●The ultra-low-power STM32L100RC device operates from a 1.8 to 3.6 V power supply (down to 1.65 V at power down) with BOR and from a 1.65 to 3.6 V power supply without BOR option. It is available in the -40 to +85 °C and -40 to +105 °C temperature ranges. A comprehensive set of power-saving modes allows the design of low-power applications.
●Key Features
● Ultra-low-power platform
● 1.65 V to 3.6 V power supply
● -40 °C to 105 °C temperature range
● 0.29 µA Standby mode (3 wakeup pins)
● 1.15 µA Standby mode + RTC
● 0.44 µA Stop mode (16 wakeup lines)
● 1.4 µA Stop mode + RTC
● 8.6 µA Low-power run mode
● 185 µA/MHz Run mode
● 10 nA ultra-low I/O leakage
● 8 µs wakeup time
● Core: ARM® Cortex® -M3 32-bit CPU
● From 32 kHz up to 32 MHz max
● 1.25 DMIPS/MHz (Dhrystone 2.1)
● Memory protection unit
● Reset and supply management
● Low-power, ultrasafe BOR (brownout reset) with 5 selectable thresholds
● Ultra-low-power POR/PDR
● Programmable voltage detector (PVD)
● Clock sources
● 1 to 24 MHz crystal oscillator
● 32 kHz oscillator for RTC with calibration
● High Speed Internal 16 MHz
● Internal low-power 37 kHz RC
● Internal multispeed low-power 65 kHz to 4.2 MHz
● PLL for CPU clock and USB (48 MHz)
● Pre-programmed bootloader
● USB and USART supported
● Development support
● Serial wire debug supported
● JTAG supported
● 51 fast I/Os (42 I/Os 5V tolerant), all mappable on 16 external interrupt vectors
● Memories
● 256 Kbytes of Flash memory with ECC
● 16 Kbytes of RAM
● 4 Kbytes of true EEPROM with ECC
● 20-byte backup register
● LCD Driver for up to 8x28 segments
● Analog peripherals
● 12-bit ADC 1Msps up to 20 channels
● 12-bit DACs 2 channels with output buffers
● 2x ultra-low-power-comparators(window mode and wakeup capability)
● DMA controller 12x channels
● 9x peripheral communication interfaces
● 1x USB 2.0 (internal 48 MHz PLL)
● 3x USARTs
● Up to 8x SPIs (2x I2Ss, 3x 16 Mbits/s)
● 2xI2Cs (SMBus/PMBus)
● 10x timers: 6x 16-bit with up to 4 IC/OC/PWM channels, 2x 16-bit basic timers, 2x watchdog timers (independent and window)
● CRC calculation unit