Description
●The Concerto™ family is a multi-core system-on-chip microcontroller with independent communication and real-time control subsystems. The F28M35x is the first series in the Concerto family.
●The communications subsystem is based on the industry-standard 32-bit ARM®Cortex™-M3 CPU and features a wide variety of communication peripherals, including Ethernet 1588, USB OTG with PHY, CAN, UART, SSI, I2C, and an external interface.
●The real-time control subsystem is based on TI’s industry-leading proprietary 32-bit C28x™ Floating-Point CPU and features the most flexible and high-precision control peripherals, including ePWMs with fault protection, and encoders and captures—all as implemented by TI’s C2000™ Piccolo™ and Delfino™ families. In addition, the C28-CPU has been enhanced with the addition of the Viterbi, Complex Math, CRC Unit (VCU) instruction accelerator that implements efficient Viterbi, Complex Arithmetic, 16-bit FFTs and CRC algorithms.
●A high-speed analog subsystem and supplementary RAM memory is shared, along with on-chip voltage regulation and redundant clocking circuitry. Safety considerations also include Error Correction Code (ECC), Parity, and Code Secure Memory, as well as documentation to assist with system-level industrial safety certification.
●Features
●F28M35x ( Concerto™) MCUs
●• Host Subsystem — ARM Cortex™-M3
●– 100 MHz
●– Embedded Memory
●• Up to 512KB Flash (ECC)
●• Up to 32KB RAM (ECC/Parity)
●• Up to 64KB Shared RAM
●• 2KB IPC Message RAM
●– 5 Universal Asynchronous Receiver/Transmitters (UARTs)
●– 4 Synchronous Serial Interfaces (SSIs)/Serial Peripheral Interface (SPI)
●– 2 Inter-integrated Circuits (I2Cs)
●– Universal Serial Bus On-the-Go (USB-OTB) + PHY
●– 10/100 ENET 1588 MII
●– 2 Controller Area Networks (CANs)
●– 32-Channel Direct Memory Access (μDMA)
●– Dual Security Zones (128-Bit Password per Zone)
●– External Peripheral Interface (EPI)
●– Micro Cyclic Redundancy Check (µCRC) Module
●– 4 General-Purpose Timers
●– 2 Watchdog Timer Modules
●• Clocking
●– On-chip Crystal Oscillator/External Clock Input
●– Dynamic PLL Ratio Changes Supported
●• 1.2-V Digital, 1.8-V Analog, 3.3-V I/O Design
●• Interprocessor Communications (IPC)
●– 32 Handshaking Channels
●– 4 Channels Generate IPC Interrupts
●– Can be Used to Coordinate Transfer of Data Through IPC Message RAMs
●• Control Subsystem — TMS320C28x™ 32-Bit CPU
●– 150 MHz
●– Embedded Memory
●• Up to 512KB Flash (ECC)
●• Up to 36KB RAM (ECC/Parity)
●• 2KB IPC Message RAM
●– IEEE-754 Single-Precision Floating-Point Unit (FPU)
●– Viterbi, Complex Math, CRC Unit (VCU)
●– Serial Communications Interface (SCI)
●– Serial Peripheral Interface (SPI)
●– Inter-integrated Circuit (I2C)
●– 6-Channel Direct Memory Access (DMA)
●– 9 Enhanced Pulse Width Modulator (ePWM) Modules
●• 18 Outputs (16 High-Resolution)
●– 6 32-Bit Enhanced Capture (eCAP) Modules
●– 3 32-Bit Enhanced Quadrature Encoder (eQEP) Modules
●– Multi-Channel Buffered Serial Port (McBSP)
●– One Security Zone (128-Bit Password)
●– 3 32-Bit Timers
●• Analog Subsystem
●– Dual 12-Bit Analog-to-Digital Converters (ADCs)
●– Up to 2.88 MSPS
●– Up to 20 Channels
●– 4 Sample-and-Hold (S/H) Circuits
●– Up to 6 Comparators With 10-Bit Digital-to-Analog Converter (DAC)
●– On-chip Temperature Sensor
●• Up to 74 Individually Programmable, Multiplexed GPIO Pins
●• Package
●– 144-Pin RFP PowerPAD™ Thermally Enhanced Thin Quad Flatpack (HTQFP)
